For Public Comment
Technical Specification for the WaterMark Certification Scheme
This Technical Specification sets out requirements for metallic and plastic-bodied waste pipe outlets and gratings, separate or integral, for sanitary plumbing applications.
The proposed revisions for the 2023 version include the following: -
Amendments to Section 5 – Materials. In particular, clause 5.1.2, metallic components.
Addition of clause 8.5.2...More
For Public Comment
Notice of Direction on annual factory inspections for lead free WaterMark certified products
In 2021 the Australian Building Codes Board (ABCB) decided to limit the allowable lead content in plumbing products, which contain copper alloys and are intended for use in contact with drinking water, to a weighted average lead content of not more than 0.25%.
A 3 year transition period to comply with this requirement is provided in the...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
Standards Australia's WS-003 committee has released a Public Comment draft to AS 1172.7 - Sanitary plumbing products, Part 7 Waterless urinals. The public comment period seeks comments from WaterMark stakeholders on the changes to the document.
Once published this Standard is intended to be adopted within the WaterMark Certification Scheme to replace WMTS-459 and WMTS 469.
The objective of...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
The proposed amendments to Technical Specification, WMTS-052 Metallic-bodied inlet pressure control valves greater than DN 50 , include the following proposed amendments:-
Clause 9.1 scaling factor for a product as determined within AS/NZS 4020 to be tested as ‘in-line’ devices and not ‘end of line’ devices.
Clause 5.2.3 (d) amended to align with current...More
Overview
As a result of the COVID-19 pandemic, there is a renewed focus on Indoor Air Quality (IAQ) in buildings, with extensive research being undertaken by governments, industry and academics.
The ABCB is reviewing and updating its IAQ Handbook to ensure it reflects the latest scientific evidence from the COVID-19 pandemic.
You can contribute to the review and update of the handbook by helping to identify domestic and international research that may be relevant.
...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
In resolving round 1 public comment for draft WMTS-536, technical changes were identified, which resulted in redrafting the test methods contained within Section 9. The ABCB wishes to consult again on the proposed technical changes to WMTS-536 before final publication.
A download link to the public comment draft and the form preview is provided below.
NOTE: Clicking on the...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This Specification sets out requirements for a plastic bodied in-wall mounted urinal that is concealed when not in use and opens when user enabled by non-contact sensor automatic operation. The urinal is integrated with components enabling direct connection to the water supply and sanitary plumbing system.
A download link to the public comment draft and the form preview is provided...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This specification includes requirements for air valves for plumbing applications. The air valves covered by this specification are limited to anti-slam valves within the scope of AS 4956. Additionally, air valves for plumbing applications are limited to the requirements of this specification. This specification is applicable to anti-slam air valves from DN 15 to DN 250, with a maximum operating...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
WMTS 104 was amended in 2018 to include specific requirements for macerating units; some of the requirements have been found to be restrictive and not plumbing-related. In particular, the PAS 29 maceration test is related to the pulp container manufacture, not the appliance. The test requirements that are included are related to the ongoing requirements of the manufacturer, not type tests....More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This Specification sets out requirements for plastic bodied fixture connector adaptors. These adaptors are used for the connection of fixtures to the sanitary plumbing system and enable connection due to misalignment. Applications include water closet pans, baths and showers.
A download link to the public comment draft and the form preview is provided below.
NOTE: Clicking on the...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
In resolving round 1 public comment for draft WMTS-533, technical changes were identified, which required redrafting. The changes included expansion of the material section and an addition of a functional test for the wet well washer. The ABCB wishes to consult again on the proposed changes to WMTS-533 before final publication.
Note:- Only comments relating to the...More
The Australian Building Codes Board (ABCB) is proposing to update the energy efficiency provisions for residential buildings in the 2022 edition of the National Construction Code (NCC). The proposed provisions are included in stage 2 of the NCC 2022 public comment draft (PCD).
An in-depth analysis of the impacts (both costs and benefits) of the proposed provisions is now open for comment. This analysis is presented in a Consultation Regulation Impact Statement (CRIS).
...More
The National Construction Code (NCC) is updated every 3 years, based on industry research, public feedback and policy directions from governments to the Australian Building Codes Board (ABCB) between publishing cycles.
Updated content is included in the public comment draft (PCD) for consultation, seeking feedback on the suggested amendments and/or inclusions in the next edition of the NCC.
To help reduce the burden on stakeholders, feedback on NCC 2022 is being...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This Technical Specification sets out minimum product requirements for the connection of commercial catering appliances employed for the preparation, cooking, and holding of food to the water service and sanitary plumbing piping.
This Technical Specification does not cover sanitation aspects beyond the water system within the appliances only, i.e., from the mains water supply...More
In 2017, Building Ministers authorised an assessment of the effectiveness of compliance and enforcement systems for the Australian building and construction industry. Recommendation 19 of the resulting Building Confidence Report (BCR) is that each each jurisdiction requires registered fire safety practitioners to design, install and certify the fire safety systems necessary in commercial buildings.
In response, the BCR Implementation Team within the Australian Building Codes...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This new Technical Specification shall be read in conjunction with AS 1357.2 and sets out the requirements for metallic pressure differential bypass valves used in heated water systems up to DN32.
Valves covered under this Specification are for continuous operating temperatures not exceeding 85°C and pressures not exceeding 1000 kPa.
A download link to the public...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This new specification sets out requirements for a prefabricated washing device consisting of a rotating arm with included spray nozzles designed specifically for use with wet wells and tanks. These devices are designed to be permanently fixed to the wet well and not portable.
These devices operate on mains water supply pressure and control is integrated with the pump so as to...More
In 2017, Building Ministers authorised an assessment of the effectiveness of compliance and enforcement systems for the Australian building and construction industry. Recommendation 3 of the resulting Building Confidence Report (BCR) states that each jurisdiction requires all practitioners to undertake compulsory continuing professional development (CPD) on the National Construction Code (NCC).
In response, the BCR Implementation Team within the Australian Building Codes...More
Technical Specification for the WaterMark Certification Scheme
This Technical Specification sets out requirements for metallic and plastics bodied waste pipe outlets and gratings, separate or integral, for sanitary plumbing applications.
The objective of this revision is to amend the Stainless Steel requirements.
A download link to the public comment draft is provided below and will be available again on the commenting page.
NOTE: Clicking on the download...More
In 2017, Building Ministers commissioned an independent expert examination of systemic problems affecting compliance with the National Construction Code (NCC). The resulting Building Confidence Report (BCR) made 24 recommendations for a best practice model for compliance and enforcement, to strengthen effective application of the NCC.
Recommendation 4 of the BCR recommended action on career pathways for building surveyors. The BCR noted that the role...More
Please note
The Australian Building Codes Board (ABCB) wishes to advise that consultation on stage 1 of National Construction Code (NCC) 2022 public comment draft (PCD) has now been extended until 11:59 PM AEST Sunday 11 July.
The ABCB is cognisant of the on-going impact on industry of COVID-19, and the flow on effect of the various lockdowns experienced in many jurisdictions. The decision to extend the public comment period for stage 1 has been made in light of the current...More
The Building Confidence Report (BCR), published in 2018, identified issues with the regulatory oversight of the construction of Class 2 - 9 buildings in Australia. It noted that fire authorities lack confidence that buildings will comply with the minimum fire safety requirements of the National Construction Code (NCC).
Recommendation 8 of the BCR is: That, consistent with the International Fire Engineering Guidelines, each jurisdiction requires developers, architects,...More
For Public Comment
Technical Specification for the WaterMark Certification Scheme
This new WaterMark technical specification sets out requirements for pre-packaged wastewater pumping wells to convey wastewater from multiple fixtures from a single dwelling to the gravity sewer invert level.
The pre-packaged wastewater pumping well may be installed above or below ground with a working volume depending on tank capacity and manufactured complete with pumps, associated...More
In 2017, Building Ministers commissioned an independent expert examination of systemic problems affecting compliance with the National Construction Code(NCC). The resulting Building Confidence Report (BCR) made 24 recommendations for a best practice model for compliance and enforcement, to strengthen effective application of the NCC.
Recommendation 21 of the BCR is that: Building Ministers agree a position on the establishment of a compulsory product certification...More
The Building Confidence Report (BCR), published in 2018, identified issues with the regulatory oversight of the construction of Class 2 - 9 buildings in Australia. It noted that owners of Class 2 - 9 buildings do not always receive complete information about their buildings, which affects their ability to properly maintain their buildings and make informed decisions about their use. This may impact the safety of building users.
Recommendation 20 of the BCR is: That each jurisdiction...More
In 2017, Building Minsters authorised an assessment of the effectiveness of compliance and enforcement systems for the building and construction industry across Australia. The resulting Building Confidence Report (BCR) made 24 recommendations for a best practice model for compliance and enforcement, to strengthen the effective implementation of the National Construction Code (NCC).
To varying degrees, all jurisdictions rely on...More
Standards Australia WS-014 Committee has released a draft of AS/NZS 3500.2:2021 for third round comment on one particular clause.
The draft will be for Combined Procedure (Ballot and PC Round 3 to run concurrently) for 2 weeks
Comment will only be invited on the reinstatement of ‘accessible and’ into Clause 6.11.3
No other comments will be discussed/resolved that are outside of this change or that relate to any other text in the draft
Links to the...More
A small amount of lead is currently used in the manufacture of some plumbing products and is permitted by Australian Standards. The exact lead content of products varies by component, although some products in contact with drinking water contain up to 6% lead as a proportion of raw material.
As part of the ABCB’s Lead in Plumbing Products Project , the ABCB commissioned a literature review in 2018 on the extent plumbing products and materials may...More
Building Ministers authorised an assessment of the effectiveness of compliance and enforcement systems for the building and construction industry across Australia. The resulting Building Confidence Report (BCR) notes that there are significant differences across jurisdictions in the number of inspections required and the notification stages. This ranges from no mandatory inspections to very few inspections for domestic buildings. For commercial buildings many jurisdictions rely on the...More
In 2017, Building Minsters authorised an assessment of the effectiveness of compliance and enforcement systems for the building and construction industry across Australia. Amongst other recommendations t he resulting Building Confidence Report (BCR) recommended that there be a statutory duty on design practitioners to prepare documentation that demonstrates compliance with the National Construction Code (NCC). It also recommended a more robust approach to third party review of designs,...More